|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
ST232AB ST232AC Very high speed, ultra low power consumption 5 V powered RS-232 drivers and receivers Features Supply voltage range: 4.5 to 5.5 V Supply current no load (typ): 1.5 mA Transmitter output voltage swing (typ): 9 V Transition slew rate (typ.): 12 V/s Receiver propagation delay (typ.): 0.1 s Receiver input voltage range: 30 V Data rate (typ.): 400 kbps/s Operating temperature range: - -40 to 85 C - 0 to 70 C SO-16 TSSOP16 Description The ST232AB/AC is a 2 driver, 2 receiver device following EIA/TIA-232 and V.28 communication standard. It is particularly suitable for applications where 12 V is not available. The ST232AB/AC uses a single 5 V power supply and only four external capacitors (0.1 F). Typical applications are in: portable computers, low power modems, interfaces translation, battery powered RS-232 networks. . Table 1. Device summary Temperature range 0 to 70 C -40 to 85 C 0 to 70 C -40 to 85 C Packages SO-16 (tape and reel) SO-16 (tape and reel) TSSOP16 (tape and reel) TSSOP16 (tape and reel) Packaging 2500 parts per reel 2500 parts per reel 2500 parts per reel 2500 parts per reel Order codes ST232ACDR ST232ABDR ST232ACTR ST232ABTR February 2008 Rev 9 1/16 www.st.com 16 ST232AB - ST232AC Contents 1 2 3 4 5 6 7 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Typical performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 2/16 ST232AB - ST232AC Pin configuration 1 Figure 1. Pin configuration Pin connections (top view) Table 2. Pin n 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Pin description Symbol C1+ V+ C1C2+ C2VT2OUT R2IN R2OUT T2IN T1IN R1OUT R1IN T1OUT GND VCC Note Positive terminal for the first charge pump capacitor Doubled voltage terminal Negative terminal for the first charge pump capacitor Positive terminal for the second charge pump capacitor Negative terminal for the second charge pump capacitor Inverted voltage terminal Second transmitter output voltage Second receiver input voltage Second receiver output voltage Second transmitter input voltage First transmitter input voltage First receiver output voltage First receiver input voltage First transmitter output voltage Ground Supply voltage 3/16 Maximum ratings ST232AB - ST232AC 2 Table 3. Symbol VCC V+ VTIN RIN TOUT ROUT TSCTOUT Maximum ratings Absolute maximum ratings Parameter Supply voltage Extra positive voltage Extra negative voltage Transmitter input voltage range Receiver input voltage range Transmitter output voltage range Receiver output voltage range Short circuit duration on TOUT Value -0.3 to 6 (VCC - 0.3 to 13.2) 0.3 to -13.2 -0.3 to (VCC + 0.3) 30 15 -0.3 to (VCC + 0.3) infinite Unit V V V V V V V Note: Absolute maximum ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied. 4/16 ST232AB - ST232AC Electrical characteristics 3 Table 4. Electrical characteristics Electrical characteristics (C1 - C4 = 0.1 F, VCC = 5 V 10 %, TA = -40 to 85 C, unless otherwise specified. Typical values are referred to TA = 25 C). Parameter VCC power supply current Test condition No Load, TA = 25C Min. Typ. 1.5 Max. 4 Unit mA Symbol ISUPPLY Table 5. Transmitter electrical characteristics (C1 - C4 = 0.1 F, VCC = 5V 10 %, TA = -40 to 85 C, unless otherwise specified. Typical values are referred to TA = 25 C). Parameter Output voltage swing Logic pull-up current Input logic threshold low Input logic threshold high Transition slew rate Data rate Transmitter output resistance Transmitter output short circuit current Propagation delay time TA = 25C, VCC = 5V RL = 3 to 7k CL = 50 to 2500pF (1) , (2) Symbol VTOUT ITIL VTIL VTIH SRT DR RTOUT ISC tDT Test condition All transmitter outputs are loaded with 3k to GND TIN = 0V Min. 5 Typ. 9 5 Max. Unit V 40 A V 0.8 1.4 1.4 2 30 V V/s kbits/s 6 200 300 7 12 400 VCC = V+ = V- = 0V VOUT = 2V One TXOUT to GND TTL-CMOS IN to RS-232 OUT CL = 150pF (50% to 50%) 22 1.3 3.5 mA s 1. Measured from 3 V to -3 V or from -3 V to 3 V. 2. One transmitter output is loaded with RL = 3 k to 7 k, CL = 50 to 1000 pF. 5/16 Electrical characteristics ST232AB - ST232AC Table 6. Receiver electrical characteristics (C1 - C4 = 0.1 F, VCC = 5 V 10 %, TA = -40 to 85 C, unless otherwise specified. Typical values are referred to TA = 25 C). Parameter Receiver input voltage operating range RS-232 input resistance RS-232 input threshold low RS-232 input threshold high RS-232 input hysteresis TTL/CMOS output voltage low TTL/CMOS output voltage high Receiver output short circuit current Propagation delay time VCC = 5V IOUT = 3.2mA (to VCC) IOUT = -1mA (to GND) to GND to VCC CL = 150pF (1) 3.5 2 10 0.2 TA = 25C Test condition Min. -30 3 0.8 5 1.3 1.8 0.5 0.2 VCC-0.2 10 mA 30 0.1 0.5 s 2.4 1 0.4 Typ. Max. 30 7 Unit V k V V V V V Symbol VRIN RRIN VRIL VRIH VRIHYS VROL VROH ISCR tDR 1. RS-232 in to TTL-CMOS out (from 50% to 50%) 6/16 ST232AB - ST232AC Typical application 4 Figure 2. Typical application Application circuit (1) (2) 1. C1-4 capacitors can even be 1F ones 2. C1-4 can be common or biased capacitors Table 7. C1 0.1 Capacitance value (F) C2 0.1 C3 0.1 C4 0.1 C5 0.1 7/16 Typical performance characteristics ST232AB - ST232AC 5 Figure 3. Typical performance characteristics (Unless otherwise specified TJ = 25 C) Driver voltage transfer Figure 4. characteristics Drive short circuit output current vs temperature Figure 5. Receiver threshold vs supply voltage Figure 6. Driver output capability current vs output voltage 8/16 ST232AB - ST232AC Figure 7. Driver short circuit supply current vs temperature Figure 8. Typical performance characteristics Receiver threshold vs temperature 9/16 Package mechanical data ST232AB - ST232AC 6 Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK(R) packages. These packages have a lead-free second level interconnect. The category of second Level Interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. 10/16 ST232AB - ST232AC Package mechanical data SO-16 mechanical data Dim. A a1 a2 b b1 C c1 D E e e3 F G L M S 3.8 4.6 0.5 9.8 5.8 1.27 8.89 4.0 5.3 1.27 0.62 8 (max.) 0.149 0.181 0.019 10 6.2 0.35 0.19 0.5 45 (typ.) 0.385 0.228 0.050 0.350 0.157 0.208 0.050 0.024 0.393 0.244 0.1 mm. Min. Typ. Max. 1.75 0.25 1.64 0.46 0.25 0.013 0.007 0.019 0.004 Min. inch. Typ. Max. 0.068 0.010 0.063 0.018 0.010 0016020D 11/16 Package mechanical data ST232AB - ST232AC TSSOP16 mechanical data mm. Dim. Min. A A1 A2 b c D E E1 e K L 0 0.45 0.60 0.05 0.8 0.19 0.09 4.9 6.2 4.3 5 6.4 4.4 0.65 BSC 8 0.75 0 0.018 0.024 1 Typ. Max. 1.2 0.15 1.05 0.30 0.20 5.1 6.6 4.48 0.002 0.031 0.007 0.004 0.193 0.244 0.169 0.197 0.252 0.173 0.0256 BSC 8 0.030 0.004 0.039 Min. Typ. Max. 0.047 0.006 0.041 0.012 0.0079 0.201 0.260 0.176 inch. A A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 0080338D 12/16 ST232AB - ST232AC Package mechanical data Tape & reel SO-16 mechanical data mm. Dim. Min. A C D N T Ao Bo Ko Po P 6.45 10.3 2.1 3.9 7.9 12.8 20.2 60 22.4 6.65 10.5 2.3 4.1 8.1 0.254 0.406 0.082 0.153 0.311 Typ. Max. 330 13.2 0.504 0.795 2.362 0.882 0.262 0.414 0.090 0.161 0.319 Min. Typ. Max. 12.992 0.519 inch. 13/16 Package mechanical data ST232AB - ST232AC Tape & reel TSSOP16 mechanical data mm. Dim. Min. A C D N T Ao Bo Ko Po P 6.7 5.3 1.6 3.9 7.9 12.8 20.2 60 22.4 6.9 5.5 1.8 4.1 8.1 0.264 0.209 0.063 0.153 0.311 Typ. Max. 330 13.2 0.504 0.795 2.362 0.882 0.272 0.217 0.071 0.161 0.319 Min. Typ. Max. 12.992 0.519 inch. 14/16 ST232AB - ST232AC Revision history 7 Table 8. Date Revision history Document revision history Revision 7 8 9 Order codes updated. Added Table 1. Modified: Table 1 on page 1. Changes 27-Oct-2006 14-Nov-2007 08-Feb-2008 15/16 ST232AB - ST232AC Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2008 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 16/16 |
Price & Availability of ST232AB |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |